| Uncoilers and Coil Handling |
| Kent |
Uncoiler 3K Double |
3,000LB double uncoiler with drag brake 1 year warranty (new) |
$13,900 |
| COE |
Uncoiler 6K Double |
6,000LB Double with Drag Brakes, 60” OD, Manual Exp. Manual Rotation, 18’ Wide Plus |
$12,900 |
| COE |
Uncoiler 6K Double |
6,000 LB double uncoiler with drag brake 1 year warranty (new) (For 100 FPM Max) |
$16,000 |
| |
|
|
|
| Kent |
Coil Car |
20K Coil Car, Self Contained Hydraulics and controls |
$12,500 |
| Kent |
4 arm Turnstile |
4 Arm Turnstile, 30K per arm, Very Good Condition (Optional Pull On Arm) |
$20,000 |
| Welders |
| Guild |
End Welder DNA100-3 |
4” max by .008 to .030” by 4”, Coil end welder, shear, and planisher, Exc Cond. |
$15,000 |
| Lee Shaffer |
C11DC End Welder |
7” by .060” manual shear and clamps. .012” min. Auto TIG Portable welder |
$7,900 |
| Kent |
End Welder10-135PMA |
10” by .110” Air shear and clamps, auto TIG welder, portable. (Excellent with Warranty) |
$9,900 |
| Kent |
End Welder H96F |
60” by .250” Capacity, Left to Right. Price for New is $250,000 |
$105,000 |
| Kent |
10-065 PCMS |
10” by .065” max and .013” by 1” min coil end welder. Right to Left (Like New) |
$13,000 |
| Kent |
C21DC |
Light gauge machine for .008 min. at 1” and up to 10” by .060” max 6 month warranty (new price $23,000) |
$14,000 |
| High Frequency Tube Welders |
| Thermatool |
TMI-300 R6 |
|
$80,400 |
| Thermatool |
VT-100 R6 |
|
$33,600 |
| Thermatool |
VT-200 R6 |
480 VAC, Complete with all output trunking and leads, new 16:2 output RF transformer |
$64,800 |
| Thermatool |
TI-150 R6 |
460 VAC, 400 Amps, 60 Hz |
$69,600 |
| Thermatool |
TMI-500 R6 |
460 VAC,1200 Amps, 60 Hz Rebuilt and with a warranty |
$152,900 |
| Thermatool |
60KW HF VT60 |
Induction type welder with vacuum tube. Was used to run .060” by 2” Diameter Tube |
$32,500 |
| Strip Accumulators |
| Kent |
Accumulator H Coil HC50 |
Kent Horizontal accumulator 10” x .083” max, 300 FPM line speed.
Built 2006, NEVER INSTALLED LIKE NEW CONDITION must check availability |
$89,000 |
| Kent |
Accumulator R30LE Floop |
3” to 12”, .042” to .156”, Left to Right, 600 to 2,000 Feet Storage
(Sale pending, Check Availability) |
$75,000 |
| Kent |
Accumulator R221RE Floop |
.028” to .120” 2” to 10” Right to Left Floop in very good condition. (May go down to .023”) |
$94,000 |
| Kent |
R253RH NE |
7” by .105” Kent Corporation Floop in good condition.
Fixed width required manual adjust for side guides. |
$49,000 |
| Kent |
Accumulator R251RH Floop |
1.5” to 6” by .095” Max. DC Drive Upgrade |
$48,900 |
| Cut Offs, Recuts and Tube Equipment |
| Tru-Motion |
Recut ES300 |
1” – 3” Round Supported Shear Recut with Bundle Loader |
$99,900 |
| Haven |
Recut 871 |
.196” - 1-1/2” OD, 80” Max Length |
$69,900 |
| Haven |
Recut 871 |
.196” - 1-1/2” OD, 80” Max Length |
$69,900 |
| Haven |
Recut 871 |
196” - 1-1/2” OD, 120” Max Length |
$64,900 |
| Haven |
Recut 872 |
½” – 3” Round, ½” – 2-1/8” Square, 120” Max Length SOLD! |
$90,900 |
| Haven |
Recut 873 |
½” – 3” Round, ½” – 2-1/8” Square, 80” Max Length SOLD! |
$94,900 |
| BEWO |
Cold Saw K |
1996 Model BCH-90 complete with 24’ bundle loader, 120” x 80mm OD
with two length stops, in line brush deburr machine, Very Good Condition SOLD! |
$69,900 |
| Alpha |
Double Cut SR-41 |
Alpha Double Cut With Die In Very Good Condition. 2" x .125” Max.
New Price Is About $385,000 REDUCED! |
$109,000 |
| Alpha |
SR12 |
Alpha Swinging ram 2 post cutoff, 3" x .134", extra die set, blades, sleeves, etc. $10K worth of parts, test run with accelerator before ship |
$79,900 |
| Alpha |
CFR-3006-49 |
3.125” Double Cut. 2” by 3” Rectangle and 2.5” Square) .154” wall 500FPM Like New! |
$325,000 |
| Thermatool |
60KW HF VT60 |
Induction type welder with vacuum tube. Was used to run .060” by 2” Diameter Tube |
$32,500 |
| BEWO |
RCH-90 Cold Saw |
2001 Complete with 24' bundle loader. 80" Max by 90mm OD Max.
In line Burrmaster model 2 (2005) Photos Available. SOLD! |
$89,900 |
| Haven |
Recut 875 |
1" to 5" Round, 120" Max Length. Late Model, Very Good Condition SOLD! |
$134,900 |
| Mair |
Tube Stacker |
3/4” to 3” OD, 6’ to 22’ Length, 8” x” to 24” x 20” Bundles.
Rounds, Squares and Rectangles! |
$135,000 |
| BEWO |
DCH 70 High Speed
Cutting Saw
|
Main System and Discharge Table, Bundle Loader and Integrated Deburring Unit. Double cut two at a time for High Production. 7 Meter bundle loader with plastic covers for non-marking. Reversing chains to aid in getting the tubes into a single layer. Length stop for up to 157" with DRO
- Bundle loader attached to saw with length capacity up to 23’
- Integrated in-line deburring unit
- Discharge table to a maximum length of 157” with DRO readout on hydraulic target
- Diameter range ½” to 2.750” round, ½” to 2.250” square
- Length from approximately 6” to 157” on direct transfer through deburring unit
- Parts shorter than 6” are dumped automatically to the rear of the discharge table
- 415/3/50 Hz voltage
- Machine is sold as-is / where-is. There is no warranty on the machine
- Jaw sets for 15-25, 25-40, 40-70mm OD
- Reconditioned in 2008
|
$115,000 |
| Mair |
Packaging Line |
Rounds, Squares and Rectangles, Diameter: 3/4" – 3”, Length: 6' - 22', Thickness: .039" - .118", 76mm (3") Bundle Dimensions: 8" x 8" - 24" x 20", Side Base of Hexagonal Pack: 45" - 12", Max Bundle Weight: 2 Tons Complete Line with Variable Speed DC Drives Siemens PLC Controls |
$150,000 |
| Adige |
CM501 |
½” to 3” OD Cold Saw with Material Supply Table. Very Good Condition! |
$14,500 |
| OTO |
2.5” Flying |
Complete and in Great Condition! 2.5" x .156" Wall, 300fpm
Double Cut |
$135,000 |
| Deburring Machines & Dedimplers |
| Kent |
Burrmaster Model 1/RHFI |
½” – 1-1/2” OD, 70” Max Length |
$9,000 |
| Kent |
Burrmaster Model 8/LHFI |
½” – 2-1/2” OD Round, 2” – 60” Max Length SOLD! |
$30,000 |
| Kent |
Burrmaster Model 1/LHFI |
3/8” – 2-1/2” OD Round, 2” Max Square, 40” Max Length. Reconditioned! |
$19,900 |
| Kent |
Burrmaster Model 1/RHFI |
3/8” – 2-1/2” OD Round, 2” Max Square, 80” Max Length |
$21,500 |
| Kent |
Burrmaster Model 1 P1 |
½” – 3” OD, 6” – 120” Max in line with Transfer for re-cut machine SOLD! |
$37,700 |
| Kent |
Burrmaster Model 1-80 |
3/8” to 3” Round, 6” to 80” Long, 460V |
$23,500 |
| Kent |
BurrmasterModel 05-060H/RHFI |
Demo, “New Machine Warranty”, ½” – 2” OD, 60” Max Length SOLD! |
$31,000 |
| Kent |
Burrmaster Model 8/RHFI |
½” – 2” OD Round, 2” – 40” Max Length. |
$17,500 |
| Kent |
Burrmaster Model 8/LHFI |
½” – 2” OD Round, 2” – 24” Max Length. Rebuilt! |
$27,500 |
| Kent |
Burrmaster Model 1-12 FHRI |
- 3/8” to 3” OD, 6” to 120” Max Length with Auto Load to Link up to Cut Off or Mill. 1994 |
$24,900 |
| RSA |
Brush Deburr NN240 |
¾” – 3-1/2” OD Round, 12” – 240” Max Length, 575/3/60 Volt |
$27,500 |
| Buckeye |
Brush Deburring Machine |
½” – 3” Round, 2” Square, 6” – 120” Length, Castor wheels, 12” OD x 18” Brushes, 460/3/60, 7.5 HP Brush Motors, ½ HP Chain drive, up to 4000 pcs/hour, Good Condition Built 1994. Rebuilt – New Machine Warranty! |
$26,900 |
| Haven |
Deburr Model 970 |
½” to 5” OD, 6” to 24” (Can be Extended) 2001. Excellent Condition! |
$29,900 |
| Loopco |
Dedimpler Heavy Duty |
Right to Left ½” – 3” OD x .134” Max Thickness, 14” – 144” Max Length,
Powered Head Adjust |
$48,000 |
| Buckeye |
DDB 24-288 Deburr Dedimple A3 |
Double end brush deburrer w/dedimpler, 6" max diameter, 24' max length, 24" brushes, 10 HP heads SOLD! |
$27,500 |
| Deburring Machines & Dedimplers |
| Contour |
Roll Former |
3.5” shaft welded shape line (in production) Complete with uncoiler, cut off etc. Thermatool HF welder, roll space, on 7.5”, Horizontal centers 15”, Vertical adjust is 4.5”, Saw cut off, Coil end welder, eddy current testing, extra rafts and more. |
$275,000 |
| Abbey Etna |
3XU-3.0Tube Mill |
3" x .160" x 450 FPM Complete Mill, Tested, with Warranty |
$749,000 |
| Yoder |
W1-1/2 Tube Mill |
Uncoiler, Kent Floop, Kent end welder, Thermatool 160KW welder,
Yoder P55 cut off, tooling, rafted stands. Great Condition! |
$299,000 |
| Yoder |
|
2.5" Tube Mill, Right to Left, 13" Rollspace, Tooling Available. Excellent Condition! SOLD! |
$199,950 |
| Yoder |
|
2’’ x .095" wall, 60HP Single Drive, 6000 LBS Double Arm Uncoiler & Shear End Welder SOLD! |
$120,000 |
| |
Complete Tube Mill Entry |
18" by .160" Tube Mill Entry with Welder , 20K Uncoiler and Horizontal Accumulator. Great Condition! |
$194,000 |
| Mair |
Tube Stacker |
3/4” to 3” OD, 6’ to 22’ Length, 8” x” to 24” x 20” Bundles. Rounds, Squares and Rectangles! SOLD! |
$135,000 |
| Misc. |
| |
|
|
|
| Tox Pressotechnik |
Air press MB8 |
8 Ton Air press, 80 psi max, 3.94” Stroke, .94” Power Stroke Mfr. Feb. 1996 |
$3,500 |
| Ma-Tech |
Banding Chopper Model RC-1 K |
4 Available, Variable Feed Rate. Like New! |
$4,990 |
|
